A Clear Brushing Lacquer – Do not spray of thin.

1. Product Description: BioShield Resin Floor Finish is clear brushing lacquer for floors and furniture. Use after priming surfaces with either Primer Oil #1, Penetrating Oil Sealer #5 or Hard Oil #9. Resin Floor Finish creates a durable, flexible seal on many types of flooring. Apply by brush only, do not spray, do not thin.

2. Specifications: BioShield Resin Floor Finish is suitable for use on absorbent floor surfaces including hardwood, softwood, adobe, stone, terra cotta, brick, and cork. The resulting finish is breathable and elastic and will create depth and dimension in flooring substrates of all types.

3. Application: Stir well before use. Apply two to three coats of this product by brush.

Surfaces must be absorbent, and free of dust, grease, wax, oil, nicotine and other contaminants. Wood, stone, and slate should be primed with one to two coats of BioShield Oil Primer #1. Highly absorbent wood floors, adobe, terra cotta tile, and cork should be primed with one to two coats of #5 Penetrating Oil Sealer.

As a general guide, you can plan on two coats of this product for new floors and one for recoat situations. Highly absorbent surfaces such as adobe or cork will perform best with three coats.

The maximum moisture content for softwoods should not exceed 18 percent and for hardwoods should not exceed 12 percent moisture. Before applying Primer Oil #1 very resinous woods such as teak must be cleaned with BioShield Citrus Thinner, and other exotic woods should be wiped with an alcohol thinner (ethanol).

Best results are obtained by applying this product with a professional quality natural bristle brush.  Light sanding between coats will improve the surface and remove small irregularities and particles. Recoat after 12-24 hours.

Most woods should be sanded with #120 sandpaper. Finer sanding and smoothly planed surfaces will inhibit oil penetration. When sanding, move in the direction of the grain to prevent scratches.

4. Safety Precautions: Provide for adequate ventilation while working with the product and during the drying time.
   
   Oil-soaked rags are self-combustible and should be discarded in a water-filled container. Keep away from open flame. Keep out of reach of children.

5. Coverage: Depending on absorbency of surface 100-150 square feet per liter.

6. Drying Time: 12-24 hours between coats, depending on climate, temperature and humidity. Product is fully cured after two to three weeks. During this curing time it is not recommended to wet the surface with water.

7. Cleanup & Storage: Use BioShield Citrus Thinner for spot clean-up and for cleaning brushes and tools. Unused contents should be kept in a well sealed container in a cool, dry place. Do not store near heat or open flame. In case of spillage, use absorbent material such as sand or cat litter. Dispose of such material and other excess by drying the contents out and in accordance with local, state and federal ordinances.

8. Ingredients: Linseed Oil, Soy Alkyd Resin, Colophony (Rosin), Isophar, Lead-free Dryers (Zircon Octoat, Cobalt Octoat), Silica, and Oximes (Anti-skinning Agent). VOC is less than 350 Grams per Liter – product must not be thinned any further. Do not spray - apply by brush only.

9. Color: Clear to lightly amber. While enhancing the grain of the wood most natural oils will slightly deepen the color of the wood.

10. Product Number and Container Sizes:

Item #4 – 0.10 Liter (3.4 Fl. Oz.) – 0.75 Liter (25.36 Fl. Oz.) – 2.50 Liter (84.44 Fl. Oz.)

Disclaimer: BioShield products are guaranteed to give satisfactory performance only if used as recommended. Liability shall be limited to refund of purchase price or the replacement of a defective product. There are no other warranties expressed or implied.

Disclaimer: BioShield products are guaranteed to give satisfactory performance only if used as recommended. Liability shall be limited to refund of purchase price or the replacement of a defective product. There are no other warranties expressed or implied.